Looking for Beginner wood carving videos?
How to carve using different types of wood for Ancient Greek Acanthus, taught online
How to carve using different types of wood for Ancient Greek Acanthus is mostly drawing. You draw it full size right on the board, stop-cut the outline, take the ground away, then shape each lobe from the top down. The Greek leaf sits shallow and it holds a stiff, formal shape, so the layout decides the carving long before the mallet does.
After all these years with this leaf, the first hour is still the same. A pencil and a board. The chisels stay where they are.
A lot of you land here after typing Beginner wood carving videos into a search box. Right. Before you compare anybody, here is the leaf and the order the tools come out.
How to carve using different types of wood for Ancient Greek Acanthus starts with a pencil
Put the leaf on the wood at the size it will be carved. A traced printout gets you through one leaf and leaves you stuck on the next.
A leaf you draw yourself teaches your hand the curve before the gouge ever touches it. Trace somebody else's line and your hand learns nothing, so the first lobe that fights the grain will stop you cold.
Begin with a rectangle. Put a center line down it, then the two arcs that carry the leaf. Everything else follows.
Why draw it full size when Beginner wood carving videos can hand you a pattern?
Take the pattern, carve it, and then draw that leaf from nothing until it stops being hard.
I was sixteen when I started my apprenticeship with a fine art master in Russia, and the thing he beat into me was not how to hold a chisel. Design is not drawing on paper. It is the laws of space, rhythm and repetition, plus knowing exactly what your tool will and will not do. He taught me to think like a tool. Somebody handed me that in a cold workshop and I never gave it back.
A pattern gets you a shape. Drawing it yourself gets you the reasons. You need both, and most people stop after the first one. A printed sheet is usually the very first thing Beginner wood carving videos will hand you.
Is the Greek acanthus the same leaf as the Roman one?
Same plant. Not the same leaf. Greek stays narrow and pointed, Roman opens and curls and goes deep.
A man waited until the room emptied at a woodworking school, then came over. He said it had never crossed his mind. For him, acanthus meant the thing he had seen a hundred times on Chippendale chairs, and that was the end of it.
The differences are small on paper and enormous under a gouge, so they get their own courses. Carving Greek Acanthus Leaf runs 16 lessons. Carving Roman Acanthus Leaf runs 17. There is a Corinthian one at 7 lessons, a Byzantine one, and one built from a design somebody drew in 1903.
Acanthus gets everywhere. I went down to St. Augustine in Florida, the oldest city in the country, and walked around the old fort, Castillo de San Marcos. Cannons. Cast iron, sitting outside for three hundred years. Somebody put acanthus on a cannon.
A short answer to "How to carve using different types of wood for Ancient Greek Acanthus"
Six steps, and five of them are about depth. Get the order wrong and you will spend an evening chasing a lobe you already cut away.
- Draw the leaf full size, on the wood itself.
- Cut a stop line right on the outline with a V-tool. Do not cut the line away.
- Take the background down to one even depth. Every corner of it, and only then start shaping.
- Rough the big masses. Start with the highest lobe and work your way down.
- Model the pipes and the eyes. Now it starts to look carved.
- Undercut the edges. Last. Undercut too soon and a lobe goes.
Most people lose the leaf somewhere in steps two and three. They shape before the ground is flat, and then the ground can never be flattened without eating the shape they just made.
The honest answer to "How to carve using different types of wood for Ancient Greek Acanthus" is that list, repeated until your hand stops needing it.
How many gouges do you need before day one of Beginner wood carving videos?
Three, and one of them is a V-tool. A shallow gouge for the broad sweeps, something deeper for the pipes and the eyes, and the V-tool for your stop line. A mallet if your wrist is tired of arguing.
Sharp always beats costly. I have watched a man with one honed chisel outwork a room full of people holding four hundred dollar sets, and it was not close. Sharpening is the skill that takes years. That truth lands badly, so I lead with it, before you pay a cent to Beginner wood carving videos.
Buy wood, not another gouge. Basswood, lindenwood, limewood, whatever your part of the world calls it. Construction lumber will take your edges off and your interest with them. Real carving wood is pricey and I say so plainly. You have to be real.
Good. Shall we carve?
What the wood decides for you
Basswood is forgiving and oak is not. The leaf is made of thin lobes going in all directions, so half of them cut against the grain whatever you do.
Which is why beginners start there. The fibers are short and even, so a lobe that runs the wrong way still slices instead of tearing out. Red oak answers the same cut with a splinter the length of your thumb.
Later, when your hand knows the leaf, move to walnut. Gorgeous, and it shows up careless work in daylight. By then you can afford the argument.
What should Beginner wood carving videos show you before you pay for it?
Ask them for the drawing stage. Skip the finished piece. You want the part where somebody explains why the line sits there.
A photograph of a finished leaf proves only that somebody owns a camera. Teachers and performers part company at the pencil stage. Put that test to Beginner wood carving videos, mine included.
A couple of other things worth checking. Does the course go all the way to the end, including the parts that go wrong? And can you see the tool in the cut, close, at the angle the carver sees it?
Ten minutes of anything you found under Beginner wood carving videos will tell you whether it can really answer "How to carve using different types of wood for Ancient Greek Acanthus".
The School of Woodcarving is a 501(c)(3) non-profit. Tuition is $25 a month and it opens all 48 courses and 621 lessons, acanthus included, and the rest with it. It renews automatically every month and you can stop it whenever you like. This money supports orphans and widows, which is the point for me.
Frequently asked questions
Can a beginner carve the Greek acanthus?
Yes, and it is a better first ornament than most. The leaf is shallow, the shapes are large, and there is very little undercutting. Start with a panel about 6 by 8 inches.
Do I need the pattern, or can I draw my own?
The course comes with the full size pattern as a download, so you have it either way. Use it for the first leaf. Draw the second one yourself.
What wood should I use for a Greek acanthus leaf?
American basswood, or lindenwood and limewood if that is what your country sells. Avoid construction pine, and leave oak alone until the leaf is familiar.
How long does one leaf take?
Two or three evenings is normal for a first leaf. The drawing is often the longest part of it.
Where is the school?
Online. You watch and carve at your own bench, at whatever hour suits you, so there is nothing to drive to. Alexander also teaches in person at woodworking schools through the year.
What is the short version of "How to carve using different types of wood for Ancient Greek Acanthus"?
Draw it full size, cut a stop line on the outline, drop the background to one even depth, then shape the lobes tallest first and undercut them last.
Who teaches these lessons?
Alexander Grabovetskiy, a master carver and International Woodcarver of the Year, who has been carving for over forty years.