Looking for Academy of wood carving?
How to carve using power tools for Ancient Greek Acanthus, taught online
How to carve using power tools for Ancient Greek Acanthus is mostly drawing. You put the leaf on the board full size, cut around the outline, take the ground down flat, then shape the lobes, starting with the tallest. The Greek leaf sits shallow and it holds a stiff, formal shape, so the layout decides the carving long before the mallet does.
The leaf has been on my bench a long time, and the start has never moved. A pencil and a board. The gouges wait.
A lot of you land here after typing Academy of wood carving into a search box. No argument here. Before any of that, look at the leaf and the order it gets cut.
How to carve using power tools for Ancient Greek Acanthus starts with a pencil
Get the leaf onto the wood at finished size. A pencil, a board, and about twenty minutes before any steel comes out of the rack.
When you draw the leaf, your hand learns the curve ahead of the gouge. Copy a line and you learn the shape but not the reason, and the grain will find that out fast.
Begin with a rectangle. Put a center line down it, then the two arcs that carry the leaf. Everything else follows.
Why draw it full size when Academy of wood carving can hand you a pattern?
Take the pattern. It helps. Then draw the leaf yourself until you can do one from memory.
I was sixteen when I started my apprenticeship with a fine art master in Russia, and the thing he beat into me was not how to hold a chisel. Design was never about paper. It is the laws of space and rhythm, and what the tool will allow. He taught me to think like a tool. That one idea is still the whole of my teaching.
A pattern gets you a shape. Drawing it yourself gets you the reasons. You need both, and most people stop after the first one. A printed sheet is usually the very first thing Academy of wood carving will hand you.
Is the Greek acanthus the same leaf as the Roman one?
Same family, different animal. Greek is tight and pointed. Roman is open, rolled over, and much deeper.
I was teaching at a woodworking school and a man stayed behind after. He said he had never once thought about acanthus this way. For him, acanthus meant the thing he had seen a hundred times on Chippendale chairs, and that was the end of it.
The differences are small on paper and enormous under a gouge, so they get their own courses. Carving Greek Acanthus Leaf runs 16 lessons. Carving Roman Acanthus Leaf runs 17. There is a Corinthian one at 7 lessons, a Byzantine one, and one built from a design somebody drew in 1903.
Odd places carry this leaf. I went down to St. Augustine in Florida, the oldest city in the country, and walked around the old fort, Castillo de San Marcos. Cannons. Cast iron, sitting outside for three hundred years. Even the guns got one.
A short answer to "How to carve using power tools for Ancient Greek Acanthus"
Six steps, five of them about depth. Take them out of order and you will hunt a lobe that is no longer there.
- Draw the leaf full size, on the wood itself.
- Cut a stop line right on the outline with a V-tool. Keep the cut just outside the pencil line.
- Take the background down to one even depth. Every corner of it, and only then start shaping.
- Rough the big masses. Work from the top lobe downward.
- Model the pipes and the eyes. Everything before this was preparation.
- Undercut the edges. Last. Get impatient here and you will regret it.
Most of the failures happen at steps two and three. They shape before the ground is flat, and then the ground can never be flattened without eating the shape they just made.
The honest answer to "How to carve using power tools for Ancient Greek Acanthus" is that list, repeated until your hand stops needing it.
How many gouges do you need before day one of Academy of wood carving?
Three. A shallow gouge for the sweeps, a deeper one for the pipes and eyes, and a V-tool for the stop line. Add a mallet when your wrist complains.
Sharp always beats costly. I have watched a man with one honed chisel outwork a room full of people holding four hundred dollar sets, and it was not close. Sharpening is the skill that takes years. Nobody wants to hear that, so I say it early, before you pay a cent to Academy of wood carving.
The wood is where your money should go. Basswood, lindenwood, limewood, whatever your part of the world calls it. Construction lumber will take your edges off and your interest with them. Good basswood is not cheap. Nobody should tell you it is. You have to be real.
Well then. Shall we carve?
What the wood decides for you
Basswood is forgiving and oak is not. The leaf is made of thin lobes going in all directions, so half of them cut against the grain whatever you do.
Basswood earns its place for exactly that reason. The fibers are short and even, so a lobe that runs the wrong way still slices instead of tearing out. The same cut in red oak takes a thumb-long splinter with it.
Later, when your hand knows the leaf, move to walnut. Lovely wood. It will find every shortcut you took. By then you can afford the argument.
What should Academy of wood carving show you before you pay for it?
Ask to see the pencil work. Not the finished carving, not the trailer. The part where the line gets a reason.
Anybody can film a finished leaf. Twenty minutes of pencil work tells you the rest. Put that test to Academy of wood carving, mine included.
A couple of other things worth checking. Does the course go all the way to the end, including the parts that go wrong? And can you see the tool in the cut, close, at the angle the carver sees it?
Ten minutes of anything you found under Academy of wood carving will tell you whether it can really answer "How to carve using power tools for Ancient Greek Acanthus".
The School of Woodcarving is a 501(c)(3) non-profit. Tuition is $25 a month and it opens all 48 courses and 621 lessons, the entire set. It renews automatically every month and you can stop it whenever you like. A part goes to orphans and widows. That is the reason I keep doing this.
Frequently asked questions
Can a beginner carve the Greek acanthus?
Yes, and it is a better first ornament than most. The leaf is shallow, the shapes are large, and there is very little undercutting. Start with a panel about 6 by 8 inches.
Do I need the pattern, or can I draw my own?
The course comes with the full size pattern as a download, so you have it either way. Use it for the first leaf. Draw the second one yourself.
What wood should I use for a Greek acanthus leaf?
American basswood, or lindenwood and limewood if that is what your country sells. Avoid construction pine, and leave oak alone until the leaf is familiar.
How long does one leaf take?
Two or three evenings is normal for a first leaf. The drawing is often the longest part of it.
Where is the school?
Online. You watch and carve at your own bench, at whatever hour suits you, so there is nothing to drive to. Alexander also teaches in person at woodworking schools through the year.
What is the short version of "How to carve using power tools for Ancient Greek Acanthus"?
Draw it full size, cut a stop line on the outline, drop the background to one even depth, then shape the lobes tallest first and undercut them last.
Who teaches these lessons?
Alexander Grabovetskiy, a master carver and International Woodcarver of the Year, who has been carving for over forty years.