Looking for Wood carving institute?
How to carve using power tools for Ancient Greek Acanthus, taught online
How to carve using power tools for Ancient Greek Acanthus is mostly drawing. You set the leaf out full size in pencil, cut around the edge, sink the background, then model the lobes from the highest one down. The Greek leaf sits shallow and it holds a stiff, formal shape, so the layout decides the carving long before the mallet does.
The leaf has been on my bench a long time, and the start has never moved. A pencil and a board. No steel yet.
A lot of you land here after typing Wood carving institute into a search box. Right. Before you compare anybody, here is the leaf and the order the tools come out.
How to carve using power tools for Ancient Greek Acanthus starts with a pencil
Pencil goes on the wood itself, at carving size. Tape a sheet on top instead and you have skipped the only part that teaches you anything.
Once you have drawn it, your hand already knows where it is going. When you trace somebody else's line, your hand learns nothing, and the first time a lobe runs into the grain you will not know which way to turn the tool.
Start with the box. A rectangle, then the center line, then the two arcs the leaf grows out of. Everything after that hangs off those three lines.
Why draw it full size when Wood carving institute can hand you a pattern?
Take the pattern. It helps. Then draw the leaf yourself until you can do one from memory.
I was sixteen when I started my apprenticeship with a fine art master in Russia, and the thing he beat into me was not how to hold a chisel. He drilled it in that design is space and rhythm and repeat, and knowing your tool cold. He taught me to think like a tool. That one idea is still the whole of my teaching.
Patterns carry shapes. Drawings carry reasons. Almost everybody takes the first and skips the second. A printed sheet is usually the very first thing Wood carving institute will hand you.
Is the Greek acanthus the same leaf as the Roman one?
Same family, different animal. Greek is tight and pointed. Roman is open, rolled over, and much deeper.
A student caught me at the end of a class at a woodworking school. He told me he had been carving it wrong in his head for years. For him, acanthus meant the thing he had seen a hundred times on Chippendale chairs, and that was the end of it.
The differences are small on paper and enormous under a gouge, so they get their own courses. Carving Greek Acanthus Leaf runs 16 lessons. Carving Roman Acanthus Leaf runs 17. There is a Corinthian one at 7 lessons, a Byzantine one, and one built from a design somebody drew in 1903.
Acanthus gets everywhere. I went down to St. Augustine in Florida, the oldest city in the country, and walked around the old fort, Castillo de San Marcos. Cannons. Cast iron, sitting outside for three hundred years. On a gun barrel, of all places.
A short answer to "How to carve using power tools for Ancient Greek Acanthus"
Six steps, five of them about depth. Take them out of order and you will hunt a lobe that is no longer there.
- Draw the leaf full size, on the wood itself.
- Cut a stop line right on the outline with a V-tool. The line stays, the cut goes next to it.
- Take the background down to one even depth. All of it, everywhere, before you shape anything.
- Rough the big masses. The highest point comes first and governs the others.
- Model the pipes and the eyes. Everything before this was preparation.
- Undercut the edges. Last. Do it early and you will break something.
The trouble almost always lands on steps two and three. They shape before the ground is flat, and then the ground can never be flattened without eating the shape they just made.
The honest answer to "How to carve using power tools for Ancient Greek Acanthus" is that list, repeated until your hand stops needing it.
How many gouges do you need before day one of Wood carving institute?
Three. A shallow gouge for the sweeps, a deeper one for the pipes and eyes, and a V-tool for the stop line. Add a mallet when your wrist complains.
Sharp always beats costly. I have watched a man with one honed chisel outwork a room full of people holding four hundred dollar sets, and it was not close. Sharpening is the skill that takes years. It is not what anyone wants, so I say it now, before you pay a cent to Wood carving institute.
Put the money into wood. Basswood, lindenwood, limewood, whatever your part of the world calls it. A construction two by four will destroy your edges and your patience. Real carving wood is pricey and I say so plainly. You have to be real.
Well then. Shall we carve?
What the wood decides for you
Basswood lets mistakes go. Oak keeps them. The lobes run every direction, so some are always against the grain.
That is the real reason this leaf is taught in basswood. The fibers are short and even, so a lobe that runs the wrong way still slices instead of tearing out. Try the same cut in red oak and it lifts a splinter the length of your thumb.
Later, when your hand knows the leaf, move to walnut. Gorgeous, and it shows up careless work in daylight. By then you can afford the argument.
What should Wood carving institute show you before you pay for it?
Ask to see the pencil work. Not the finished carving, not the trailer. The part where the line gets a reason.
Anybody can film a finished leaf. The drawing is where a teacher either has something to say or does not. Put that test to Wood carving institute, mine included.
Two more questions to ask. Does the course go all the way to the end, including the parts that go wrong? And can you see the tool in the cut, close, at the angle the carver sees it?
Ten minutes of anything you found under Wood carving institute will tell you whether it can really answer "How to carve using power tools for Ancient Greek Acanthus".
The School of Woodcarving is a 501(c)(3) non-profit. Tuition is $25 a month and it opens all 48 courses and 621 lessons, six acanthus courses and 42 others. It renews automatically every month and you can stop it whenever you like. A part goes to orphans and widows. That is the reason I keep doing this.
Frequently asked questions
Can a beginner carve the Greek acanthus?
Yes, and it is a better first ornament than most. The leaf is shallow, the shapes are large, and there is very little undercutting. Start with a panel about 6 by 8 inches.
Do I need the pattern, or can I draw my own?
The course comes with the full size pattern as a download, so you have it either way. Use it for the first leaf. Draw the second one yourself.
What wood should I use for a Greek acanthus leaf?
American basswood, or lindenwood and limewood if that is what your country sells. Avoid construction pine, and leave oak alone until the leaf is familiar.
How long does one leaf take?
Two or three evenings is normal for a first leaf. The drawing is often the longest part of it.
Where is the school?
Online. You watch and carve at your own bench, at whatever hour suits you, so there is nothing to drive to. Alexander also teaches in person at woodworking schools through the year.
What is the short version of "How to carve using power tools for Ancient Greek Acanthus"?
Draw it full size, cut a stop line on the outline, drop the background to one even depth, then shape the lobes tallest first and undercut them last.
Who teaches these lessons?
Alexander Grabovetskiy, a master carver and International Woodcarver of the Year, who has been carving for over forty years.