Learn the trade that starts where the machines stop, without leaving Shalimar, FL.

A woodworker and a carver are not doing the same job at the bench. A woodworker makes the panel flat, square and true. A carver makes it come out of the flat. Good Woodcarving Tutorials teach the second thing, and it takes a different eye.

Ever finish good joinery and want to put a shell in the middle? Want to be the person who can put that leaf there? Then keep reading, because that is exactly the trade I teach.

Woodcarving Tutorials in Shalimar, FL, and what a club cannot give you

You can almost certainly find a club nearby, and I would go. What a club has is a table saw, a schedule and company. What it usually does not have is somebody who carves acanthus.

Carving is a narrow trade. In a room of forty woodworkers you might find one who has cut a proper leaf, and he learned it from a book. Nobody is at fault in it. It is why a person in Shalimar, FL can be surrounded by woodworkers and still have nobody to ask.

So the real question was never how far away a shop is. The question is whether the person teaching you has actually done the work.

A woodworker in Shalimar, FL can have every machine and still not carve. None of that machinery cuts a leaf. The leaf is cut by hand, by somebody who knows which way the grain will let it go, and that knowledge does not come with the equipment.

Real teaching in Woodcarving Tutorials starts where the machines stop, and that is the whole reason this school exists. It begins with Principles of Design in Wood Carving, which is a drawing course before it is a cutting course.

Where the ornament came from, and why that matters

These forms are centuries old and they were worked out carefully. Acanthus leaves, volutes, shells and running borders were all worked out over centuries by people who cut them first into stone and then into wood.

Learn the shapes properly and you can put them on anything. Learn them from a bad copy and you inherit the mistake. A leaf that turns the wrong way at the tip is wrong on every panel you ever cut it into.

The Greek form is the first one taught here. After that a Roman leaf, a Byzantine one and a Corinthian one each bend the same form in a way you can name out loud once somebody shows you. There is a course for each, and Carving Greek Acanthus Leaf is the door into all of them.

So you start on paper. Pencil, ruler, compass, and the geometry underneath the leaf. Homework, by the look of it, and the whole craft in fact.

Your first month at the bench

The honest version of the first month is short. Nobody carves a Baroque panel in week one. The work is cutting lines in a scrap of basswood until they stop tearing.

Straight cuts. Then curved cuts. Then a simple leaf, and it will look like a fish. Cut that same leaf twenty times and around the fifteenth your hand stops arguing with you, and something clicks. It happened to me too.

Now, shall we carve?

The wood and the tools for Woodcarving Tutorials

Buy less than you think and buy better than you think. A set of twelve cheap gouges in a roll will not hold an edge, and you will blame yourself.

Basswood, also sold as limewood or lindenwood. Not pine from a builders yard in Shalimar, FL, whatever the price tag says. Pine tears along the grain, dulls your edge and teaches you nothing except that carving is miserable, which is a lie.

Do not be surprised if nothing near Shalimar, FL carries basswood. Order it and wait the few days. A good board is the cheapest part of this craft and it decides half the result.

Sharpening comes with the territory, and it is the skill that takes the longest. Carving Tool Sharpening is a course of its own here for that reason, not a paragraph tacked onto something else.

Three or four gouges. One V-tool, one knife, and something to sharpen them on. Add a mallet when you get to deeper work. You get the list and the argument for the list.

What you pay for Woodcarving Tutorials

The figure is $25 a month, automatically renewed every month until you cancel. You cancel it from your own account page, and nobody phones you to ask why.

The school is a registered 501(c)(3) non-profit. Part of what you pay goes to orphans and widows, and the rest keeps the lessons being filmed. Plainly stated, that is where it lands.

What all of it is actually for

At the end of it there is a thing your grandchildren will still own. A carved panel on a cabinet door does not get thrown out. It gets moved to the next house.

Your grandchildren in Shalimar, FL could still be using it. That is not a sentimental thought. Carved furniture simply behaves that way, and the shapes are therefore worth learning properly rather than approximately.

Nobody here is going to ask what you plan to do with it. Come for one box or come for a career in Woodcarving Tutorials. The lessons are the same either way, and they wait for you.

Some students want one carved box for a daughter's wedding. Others end up carving mantels and altar screens. Both are fine. Nobody is asked which one they are.