Alexander Grabovetskiy, woodcarver, School of Woodcarving · Published 2020
What does a wood carver mean by "green tape"?
Quick answer: Part 10 of Venice Room workshop 79 has the green tape was in my garage, not at the bench, while I planned a drill hole. Other lessons put it under a paper pattern, on a petal strip, on a lid and around a curve.

Part 10 of Venice Room workshop 79 has me saying "I could use just the green tape" over a drill hole, and a roll of that tape turns up in my other lessons holding paper, shielding an edge and drawing a curve.
Ever tried to stop a drill at one depth? Ever peeled paper off a piece and found no trace of glue? Here is what I said about tape in that corbel lesson, and the other places in my wood carving lessons where a strip or a roll did a job.
What was I working on in part 10?
A tool plan comes first in this part: "I probably should grab 7 millimeters, a little bigger than a quarter-inch, on this side because I've got multiple small details." Seven millimeters is about 0.28 in, and a quarter-inch is 6.35 mm, so I planned a tool just over that size.
Then came a feeling I could not name yet: "It feels like I'm doing some kind of mistake. I feel that inside, but I don't know yet what I'm feeling yet."
One plan followed it: "that's why I'm not going to go all the way to the edge," and "I also need to deepen this side."
How was I going to reach the inner point?
I kept a line in mind: "Do not want to lose it." My aim was "what I'm after, I need to get as deep as this one going in." Then "But for that, I need to measure."
Two ways came to mind after that. One was to "just drill it, but I'm not sure the angle." The other was to dig in a step at a time, and I said "the closer to that point I get, the tinier tools I'm going to have to use."
Why did I turn to the pointing machine?
"I need to measure from the backside somehow." Next, the name of a tool: "One of the tools I really, really like, it's a pointing machine." A lesson on that tool sits at the pointing machine for wood carving. And "Sometimes it's hard to use even calipers, but pointing machine is good."
The measuring went like this: "Once I got the depth of certain points from the backside, I can actually measure from out since it's laying flat on my workbench." I added "For me, it's pretty much really easy to measure to the point right from the surface of my workbench." And "Which is a really, really good way to do."
In my words, I wanted to "access from different point." My plan: "I'll stick as far as possible this way," then "I'll change the position of my needle," and "I'll raise it to the depth. Okay. Here's my stop." Then "And now I know, so this depth is supposed to be whatever I just measured, okay?"
How did I plan to set a drill depth?
The next idea was a hole: "So now what I can do, I can actually drill." Then, "For me, it would be really easy to just drill a hole certain depth, and that is going to show me exactly the position I have to be."
A limit came with it. "Approximately three-quarter of an inch, and I do not want to drill more than that." That limit is about 19 mm. Before that I said "And let me see how much I have to drill."
Tape came next: "I'll use tape. I could use just the green tape, but it's not here." That tape was in my machine shop, "which in my case is just a garage."
My plan was a limit by eye, and my words were "But I'll tape it approximately three-quarter of an inch. Again, I'm just eyeballing it. And let me drill it."
In these frames a roll of black tape sits on the bench beside the pointing machine, and a drill bit is in my hand. The drill was to stop short, because "I really want to check first."
What did the check show about the tape?
"And yes, I need to drill another 5/8 of an inch, about 16 millimeters or so, so this tape is no good for me." Sixteen millimeters is about 0.63 in, and 5/8 in is 15.9 mm.
My reason came next: "because I've got my line a little lower than the higher region, and just bulking up." And "So that is why, actually, the depth is not really accurate."
Venice Room 79, part 11, opens with "I'll just do little by little." Then "Here you go. I've got another quarter inch," which is 6.35 mm. And "I've got about one-eighth of an inch left, about three millimeters" (3 mm is about 0.12 in).
Later still, "And all the way to my hole I drilled." And "the next I have to just measure the next position and create another hole, and that way I'll know exactly where am I supposed to be."
That was part 10. Other lessons use the same tape in green, and here are my words from them.
Why do I like green tape under a paper pattern?
In Carving Dining Table Apron, workshop 5, I said "I'm going to use a same green tape." I went on: "I like this green tape because it's sticky, but still I can easily peel out from even that tracing paper."
The next one is in Lily Box 1, part 1: "it's designed for the lacquer." Next, "And I really like how sticky, but still, it's mild enough, so I can easy, easy take it out when I need it."
In Lily Box 2, part 8, with the paper off: "just because I used that green tape, my surface is absolutely clean," and nothing sticky was left. Further on, "the green tape is sticking everywhere."
Can tape help a saw blade?
Over in Lily Box 1 I said "And if you would ask me what I mean by saving my blades." A moment later: "Yes, I'm actually saving my blades."
A second color was the plan, "and I'll use a green tape," with the glue "right on the wood."
My reason: "this tape is going to cool down and lubricate the blade," so the blade works longer without breaking.
What does a tool scratch when the tape is under it?
Sharp tools should go through the paper without a problem in that lily lesson, Lily Box 2, and through the green tape, or blue tape if you wish.
A later line: "See? I almost destroyed it. But that's a good thing that I had the green tape underneath. I actually just scratched the green tape. I did not touch the wood itself."
When the tape came off: "In my case, in your case, it could be blue, white, or any type of tape. Okay?"
What if you have no green tape?
Before the pattern went on, I said "Just any masking tape will work." Then "But I really like that green one."
The same part has "Going to apply blue tape just to mark my position." And "I think it's a good idea." Over in Lily Box 3, part 10, "see how easy I can remove just because it's a painter's tape. Really easy."
The Schaaf wood carving tools lesson has blue tape on a block: "If you don't have a blue tape in your country, you can use any painter's masking tape. Which is going to be easy later on to remove."
Can a strip of tape give a petal length?
Petal length comes up in Lily Box 10, part 3: "I can measure exactly how long all of my petals should be."
The plan was "a small strip, maybe about five millimeters. 3/16 of an inch." That is 5 mm (0.2 in), and 3/16 in is 4.8 mm. The strip was to "stick that on the inside," so I would know the exact length of my petal.
Then "Okay? So all of them should be that long." Next I planned a mark: "I'll just place a black mark."
Can tape work as a clamp?
My words for masking tape come from Lily Box 10 again, part 7: "And to hold it, I absolutely can't put any clamps, but I can get the best clamp with my green tape. That is the best clamp, masking tape." Next came "I can create a lot of pressure with that."
A small piece I glued back comes up in Lily Box 4, part 8: "that was green tape." Later, "I lowered that down a little bit."
At a lid in Lily Box 13, part 11: "My green tape also serves me as a clamp. I could use clamp to clamp together the lid and the main body."
Why did I like the idea of green tape?
In Lily Box 8, part 13: "I still have a high spot," and "I really like the idea of a green tape because I can really see what is going on." Later in that part I said it was time to lose the tape: "It's actually the last piece which is left."
Does tape protect a finished edge?
The flocking is ahead in Lily Box 13, part 10: "Protect it first, apply glue, and we're going to flock it." Then "Probably by now, you know that I really like green tape. That tape is lacquer safe, and I used the lacquer."
Of the finish I said "It's not going to pull my finish out," and "I still have to protect the edges." Later in that part: "I want to make sure I create really a nice effect. It would look like a felt material." Then "if you don't really like to protect it with blue tape or whatever, in my case, it's a green tape, you're still able to create a nice line with just carefully coming to the edge with the brush." I added "But I think the way I do it, it's much, much safer."
In part 11, with the tape coming off: "Let me remove green tape and see how it is going to look. But look at that. It's absolutely gorgeous. It just leaves absolutely nice line." Of the box I said "See, it's clean and it's soft."
How does a hinge use tape?
A drill came up again in that part, a micro drill with "the smallest of the smallest bits in it, and it's easy to operate." My tape line: "that is a number one helper when you're doing a furniture or cabinets, like a blue tape or green tape in my case. That way I'll just get exactly the same distance."
The frame shows a brass hinge held against the wood, and green tape beside it. My own words after that: "I don't want to over-drill it. So always tendency to overdo it, but I really don't want to do it, okay? So it takes a couple seconds, but it gives me a lot of control."
What can a roll of tape draw?
Venice Room 96, part 2: "I can't use a compass," and "the center is going to fall somewhere right in this hole." Of a French curve I said "But I found it is limited."
"I usually find the simple stuff helps me a lot." My answer was a roll of tape: "And this case is just the roll of green tape and this green tape going to give me a really nice, beautiful curvature."
Where did tape stand in for a gauge?
Two choices come in Venice Room 1, part 3: "I could use blue tape." Then "Or I could use double-sided tape."
Acanthus over Moldings 1, part 1: "I used just a normal printer's paper, drew my molding, and got my tape which is right above me. I've got the green tape." Next, "It's going to be a lot easier to trace and check. So those are my gauges. I can use it just to check if it fits or not."
I kept them within reach: "I keep them close by right on my workbench. That way, I can reference them any moment."
The tape across my lessons, side by side
| Job | What the tape did |
|---|---|
| Paper pattern | Sticky, but it peels away from tracing paper. |
| Saw blade | Taped on the wood, under paper and blade. |
| Tool scratch | My tool scratched the tape, not the wood. |
| Petal length | A strip planned for the inside, then a black mark. |
| Lid clamp | It stood in for a clamp on a lid. |
| Curve guide | A roll to give me a nice curvature. |
| Drill limit | Tape planned by eye, and then no good. |
Is there a spot on your own piece where a strip of tape would save a mistake? My words from these lessons sit above, each with its lesson.
Where can you watch these lessons?
You can watch part 10 in Venice Room 79, and Venice Room Part 7 holds workshops 74 to 85. The other lessons are linked in the sections above, with the Lily Box course and the Dining Table Apron course in full.
How it's done
- Reach for a pointing machine. I named it as one of the tools I really like.
- Raise the needle to the depth. The needle would go up to the depth, and that was my stop.
- Tape the limit. Tape it at about 3/4 in (19 mm), as I planned, then drill it.
- Drill, then check. Drill part of the way, because I wanted to check first.
- Read the check. Another 16 mm (0.63 in) was needed, so that tape did not work for me.
Frequently asked questions
Which tape did I name in part 10?
Green tape, kept out in my garage and not at the bench. I would use tape and set a limit by eye.
How far did I plan to drill?
I planned 19 mm (3/4 in). The check said I needed 16 mm (about 5/8 in) more.
Why was the tape no good for me?
My line sat a little lower than the higher region, and just bulking up, so the depth was not really accurate.
Which tool read the depth from behind?

About the author
Alexander Grabovetskiy
Master Wood Carver · Founder, School of Wood Carving
Alexander Grabovetskiy is a master wood carver, named International Woodcarver of the Year. He carves classical relief the old way, from acanthus leaves to full Baroque ornament. He started the School of Wood Carving, a nonprofit, to hand these skills to anyone ready to pick up a gouge.
What to carve next
